how can i customize a silver chrysler 300?

Question 1
how can i customize a silver chrysler 300?...  

Answers
1)   Why would you want to. You drive a Chrysler. - Wally Balls

2)   rims, aftermarket grill and tint the windows. sweet stealth look - joel b

3)   tints and wheels - pickmefirstplz

4)   Grills are cheap and easy, pretty snazzy. My cousin replaced his grill with a mesh looking one, really added some style. And of course, rims, tint (look at the laws where you live though). Look up headlights too, I don't really care for the square ones, but I think they'd be better if they were white HIDs instead of the piss yellow that come with it out of the factory. - Mark

5)   Tint your windows and put black rims and of course the grille. Dont go too crazy with size stick with 18-20 inch rims and your car will look a lot more classy and will look like you customized it but not sloppy like a teenager did it. also is yours a V-6 or C or SRT?

if it is a SRT try to keep it looking more stock, dont go too crazy

if it is a C you may want to change the mufflers for flowmasters, or borla

if it is a V6 consider also changing the headlights, i find the v6 headlights way uglier than the v8 - ahmedniu

6)   In my mind...17" wheels with good rubber, a good cat-back exhaust, and a Hennessey twin turbo setup. Nobody actually buys V6 300's, right? Tint hides things while it's parked. Twin turbos hide the whole car in motion...can't see what you can't keep up with. And you don't look like a douchebag with giant chrome wheels on it, trying to make your $30,000 Chrysler look like a rappers jacked up $300,000 Bentley on giant wheels like they always do. Any wheel over 18" is useless, and realistically should be illegal in my mind because they are a safety hazard, but that's all opinion. - Sean


___________________________________________________

Question 2
what would be a good name for a navy blue pt cruiser?...  when i get my license in a few months ill be inheriting my dads pt cruiser, and i want a cute pet name for it. suggestions?

it looks like this: http://gtcarlot.com/gallery/16283608-640.jpg
hahahahaha, why shouldnt i name it?

Answers
1)   Dont want to offend you...but please dont name a pt cruiser. - Derek

2)   Id do something like "Kennedy". now lets see if anyone can put the two together. - DodgeDude

3)   it's the PT LOSER for sure. - jacksprat

4)   STOVE - ken k


___________________________________________________

Question 3
the a/c in my chrystler town and country. the back a/c is working fine but the front a/c only blows on high?...  the fan motor is a new one and i tested it and it is working.

Answers
1)   very common on dodge and chrysler vans....go to your local dealer and tell them you need a blower motor resistor for your van

now i say go to dealer cause they are slightly better than ones you get from parts houses so i have found out

they are easy to install most are under dash on pasenger side or right behind the glove box on those vans - wondering

2)   You need a front blower motor resistor. - Dave

3)   The blower resister is located under the unit next to the round blower motor. You can identify it by it's oblong wire connector plug in and it only has 2 screws one on each end holding it in. - Jackolantern


___________________________________________________

Question 4
1997 concord rear-wheel drive?...  I'm not an expert on cars, but I had a 97 concord that could not handle well in the snow or bad weather. I used to burn rubber when I hit the gas too fast. I thought it was a rear-wheel drive, does anyone know if this sounds right. Please help

Answers
1)   Front wheel drive. - Mark

2)   It is for sure a front wheel drive. I used to own one. - nellybob

3)   the Concord is a Chrysler LH platform car. It has the motor sitting north to south like most rear wheel drives but is a trans axle front wheel drive car. - DodgeDude


___________________________________________________

Question 5
can a Chrysler transponder key be reprogrammed?...  I had a 06 Chrysler 300c (5.7L) and it was totaled and I still have two keys for it.

After my car was totaled i purchased a 2006 Chrysler 300 SRT-8 (6.1L) and only had one key for it. The key is now missing and I was wondering if i can take my old keys (300c) and take out the chip and put it in another key if i will be able to program it. I asked the dealer and he said he was not sure.

Please only provide FACTS and not opinions, and please only talk about chrysler products (chrysler, dodge, jeep)

Answers
1)   No. - Dave

2)   No. Chrysler chips lock when initially programmed. You won't be able to program the chip regardless, a scan tool is required. - Hillbilly Locksmith

3)   You will have to purchase a new key from a dealer and the dealer will have to take the new key and program it to the sentry chip located around the ignition switch. - Jackolantern


___________________________________________________